Whilst waiting for the police to arrive I had a look round the vehicle and did not see anything untoward, so I carefully opened the driver's door and put the key in the ignition and turned it on and it was dead. A label on the panel shows the circuits protected and the fuse locations. Looking over it today, trying to work out the add ons hydraulics and electrics , we spotted this under the drivers seat The top panel of the fusebox had melted above that green mess. Let us know if we can help you with any of your Defender needs! Pull the fuse box panel back and push up on the flasher relay base to release it from the metal support. Think I'll have to persist with a new Clarkes rotary tool with flexible extension, original Black and Decker one has just died, not bad after 15years light use!!! The flasher relay is located behind the fuse panel support in the location marked by the purple outline, but you can't reach it or at least we can't. On the 18 th June 2009 I wrote a to Hunters Southampton and sent copies to Hunters Derby and Land Rover Customer Care.
The fuse numbers are displayed on the fuse box. Yeah right, they where hoping I would forget about it. Pressing the switch causes the rear washer to operate until the switch is released. Fuse 21 - Direction indicators 10A 15. Just another idea with all the trim off and the clocks out can you drill it out from above?? What might have caused this? Need to get on your back under the steering wheel! I wouldn't replace the fusebox itself - yet. Have someone stand in back and watch as you put it in reverse.
Jul 01, 2016 You can rule out internal transmission wires. Relay - Anti-theft alarm 35. Remove the ground cable from the battery. Section 14 2a states:- For the purpose of this Act, goods are of a satisfactory quality if they meet the standard that a reasonable person would regard as satisfactory, taking into account of any description of the goods, the price if relevant and all the circumstances. Relay - Heated Front Screen 31.
F2 — 2 x Carling switch cut outs F3 — 2 x 29mm socket holes F4 — Custom cut as F4 and £10. There is a wire connection between the stop light switch and the control unit to let the system know when brakes are being applied. I did get a from the dealers and also a reply from Land Rover customer care which was marked confidential, so not knowing the full implications of publishing a confidential letter I have left it out at the moment, but I did get a follow up from the dealers which was not confidential and in conjunction with my it will give you some idea as to the content of the confidential letter. Owned numerous Land Rover vehicles of all shapes and sizes over the decades. Got new ignition and door locks handles etc so I can't wait for that joy of a job. Shown above, fuses and relays are exposed once the fuse box cover is removed. Moving the wiper switch up two positions from the off position, operates the wipers at fast speed.
So now I had to check the indicator relay. The wiper motor is earthed -1 on a black wire. The reply back from Hunters on the 11th August 2009 indicates that they had lost the p lot and it is obvious that they are incapable of understanding that the vehicle is no longer a standard vehicle once it as had modified parts fitted under warranty. Dec 02, 2012 No noise from fuel pump when you turn over the car. The park circuit operates to return the wiper to its park position. The wiper motor -1 is earthed on a black wire. Fuse 12 - Engine Control Module 10A 6.
My method, which may help future Puma ignition changers, with the limited space due to new dash tray under steering column:- 1 With my new rotary tool managed to cut through right hand bolt. A reset button is located on switch assembly. Basically I had no direction indicators and had to investigate why this was. This extra resistance causes the motor to operate at slow speed. The hard or no starting after you drive for a while could be related or a problem with the ignition coils or ignition module.
Changing the stop light switch cured it. Fuse 10 - Rear wiper relay 10A 4. Fuel pump receives power through fuel pump relay contacts. The first problem could be the fuel filter if it is getting plugged up it wont allow the fuel to flow through to your engine sufficiently, but at faster speed it will still allow the fuel to flow enough. The wipers have 2 speed settings, along with a flick wipe and single wipe facility. Visitors may view and use this web site at their own risk. Then install the relay base back onto the metal support and test your flashers.
Once tested reverse the directions above to put the console back in. Imagine they'd be harder than the collar though. The relay did turn out to be the problem for me, and as soon as the new one was fitted, the indicators and hazards worked. Here are the steps needed to get to it: Remove the fuse panel cover. Good luck with the project and hopefully the door lock change proves to be a quick job! Remove the cubby box tray and remove the three 8mm headed bolts that hold the consoles rear bracket to the seat box. I can't remember if it's blind holes or not but if not and you can get a bit down only need to go enough to remove threads one side then same other or crowbar and it'll probably crack or slide up the column. I bet there's a dead easy way if you know about it aha Hi All, Finally sorted with new Clarke's rotary tool to replace now dead Black and Decker one! See photos below should have taken during project, but they're better than nothing to illustrate method.
I'm glad this wasn't posted in the 'Technical' section. And sure enough within 48hrs at 2am in the morning the alarm went off and there was 2 persons with balaclava's round the vehicle. Will be opening a new thread as now need to change door locks and having problems, surprise, surprise!! Also after I got the vehicle back from the repairers, I rang Land Rover Customer Care, and they advised me to take the vehicle to a dealer. The next sent on the 30th June 2009 to Hunters and Land Rover customer care was a summary of the conversation with Land Rover customer care plus some options to resolve the issue. The wipers operate at slow speed.