Keyence kv series plc user manual. KV 2019-03-21

Keyence kv series plc user manual Rating: 9,7/10 897 reviews

KEYENCE KV Series User Manual

keyence kv series plc user manual

Receive the bar code data. The initial settings are made. List of commands and responses Range of available station nos. Be sure to read these messages carefully. In such a case, pay strict attention to the following contents.

Next

KEYENCE Visual KV Series User Manual

keyence kv series plc user manual

Comment 1 1 Device No. Changing all devices displayed on the screen is disabled. After the program is entered, please transfer the program and verify its operation. The screen next to the disabled screen appears. When the key is pressed and held down continuously, the quick function is activated 1. When performing input while setting the input time constant of an expansion unit to 10 µs, or when synchronizing the output of a basic unit with the output of an expansion unit, pay strict attention to the following contents.

Next

Manual

keyence kv series plc user manual

The following signals are assigned to the terminal nos. This command generates no response. Canceled when is pressed or when no key is pressed for 25 seconds x 1. For the range setting, refer to page 1-319. Set the input time constant of input 0008 to 10 µs. In the numeric value change mode of the operator screen, set the number of pulses of one encoder rotation to obtain the measurement cycle and rpm. Each relay turns on only while the corresponding switch is pressed.

Next

Programmable Logic Controller

keyence kv series plc user manual

Function 2500 Pressing F1 Customized switch 1 turns on this relay. Tips Example 1 Change the trigger on command to S. In order to produce and sell new products for Christmas, it is necessary to rebuild the production equipment. Read this chapter when problems occur during operation. Setting the input mode Follow the procedure below to set the input mode.

Next

KEYENCE BL

keyence kv series plc user manual

The mode cannot be changed. They can help reduce the time required to write programs. Cursor automatically moves to timer No. Note 2: Communications protocols for the modules to be connected must be identical; otherwise, communication will fail. Press and hold it for 3 seconds.

Next

KEYENCE KV

keyence kv series plc user manual

Note: When the scanning width is changed, the laser beam may not be properly applied to the bar codes, resulting in poor readings. The screens are changed in the following order. Note 1: Do not insert the memory card backwards. When the operation mode is changed, the backlighted color is changed. Affix the Warn- ing labels on the sensor head as shown below. Terminal lock bar 15 3.

Next

KEYENCE BL

keyence kv series plc user manual

However, the display of the preset value for a device using two lines timers and counters depends on the Bit 12 setting. Check or change the communication parameter settings of the personal com- puter. The two-line program can be realized through one line in a convenient command. Countermeasures Turn off the power, then turn it on again. Data is written in mV units. Open the relay cover on the top of the module with a screwdriver. You can use this area for other purposes.

Next

KEYENCE Visual KV Series User Manual

keyence kv series plc user manual

Thus, the bar code can be read even if it has a stain or missing part. Register the operation mode selected in step 1 above. Crimping punch Crimping grooves Cover Guide 3. Reading succeeded Reading failed 6. When the data is loaded at startup, the first relay no.

Next

KEYENCE BL

keyence kv series plc user manual

The user messages are displayed at the rising edge of inputs 0000 through 0002. Note 2: The temporary memory addresses can be changed by bit. Calculate the numerical value to be written into data memory. The counters, high speed counters, or internal utility relays latches are cleared. For this reason, you must periodically inspect the unit and connectors. This also applies to input or output only expansion units. Changing the current screen is The setting is not effective disabled, but the until the screen is screen is still changed.

Next

KEYENCE Visual KV Series User Manual

keyence kv series plc user manual

. F1 F2 F3 F4 Ladder program 0001 To display product information 0002 Display values of counters 0 and 1 with titles. When the key is pressed and held for 3 seconds, a digit to be changed begins flashing. A numeric value can be changed only for the flashing digit. Deletes all programs in memory card. The personnel of each business office are ready to help you. Mount the fixture directly to the panel.

Next