This factory service repair manual offers all the service and repair information about deutz bfm 1012 1013 engines the information on this manual covered everything you need to know when you want to repair or service deutz bfm 1012 1013 engines. Consequently, a wide range of variants are offered to meet the requirements of specific cases. Check that the cartridge is correctly seated Loosen screws and slide clamps down- against the gasket and tighten with a final wards. If you require more detail or more parts, to go through to our Service Portal and locate parts specific to your engine serial number. Unit engine with frontal radiator - After the engine has been prepared, let it See section 6. The pilot lights will go out. Before starting, make sure that nobody is standing in the imme- diate vicinity of the engine or driven machine.
Loosen the vent screw 7 slightly. Our form will allow you to enquire about five different parts. Page 1 operation manual 1012 1013 page 2 the risks involved are when carrying out maintenance repair op to be borne solely by the user erations on the engine the use of deutz use in accordance with the intended pur original parts is prescribed. Leave to preheat until pilot lights go out. Check battery and cable connections, see See section 6. Remove fuel pump belt as described in 6.
Check for leaks after starting the engine. This is a original workshop manual for deutz bfm 1012 e bfm 1013 e diesel engines in pdf format this service repair manual has easy to read text sections with high quality diagrams and instructions. Routine work should be carried out according to the schedule in 5. Temperature monitor gives warning Replace Engine gives poor performance Clean Engine not firing on all cylinders Top up Engine has little or no oil pressure Lower level. Drain off any oil residues that may be remaining.
Trial run See section 6. Loosen vent plug position 2 and sealing plug position 3. Description : Deutz bfm 1012 workshop manual engine deutz d302 repair manual diessel engines 74 pages engine deutz d 909 910 installation manual high speed diesel engines 290 pages engine deutz wp6c series operation and maintenance manual 37 pages related products for deutz bfm 1012. It should be affixed where it can be seen clearly on the engine or driven equipment. After five air cleaner services or after apart lips of discharge slot as indicated two years at the latest, replace safety Take off hood 2 and remove cartridge 3.
After repairs: Check whether all protection devices are mounted and all tools have been removed from the engine. Operators and maintenance personnel must read this manual before operating or maintaining this machine. Adjust clearance of valves marked in black on schematic. Loosen drain plug 4 and observe the draining fluid. Oils of other, comparable specifications also single-grade oils can be used.
Caterpillar® and all of the Caterpillar® engine models listed on this website are registered trademarks of Caterpillar, Inc. The filling aid is obtainable under order No. The pre- servative measures described here will protect the engine for up to 6 months. When fuel instead of water starts to flow, retighten drain plug 4. Turn engine off and wait about 10 minutes Clean filter housing 1 if very dirty. Measure the specific gravity of individual cells with a commercial hydrometer.
Should you have any questions, please call Deutz Corporation Product Support Department. This number should be quoted when enquiring about customer service, repairs or spare parts see Section 2. Technical modifications required to improve our. Close the fuel shut-off valve. Temperature monitor gives warning Replace Engine gives poor performance Clean Engine not firing on all cylinders Top up Engine has little or no oil pressure Lower level. Loosen drain screw 9 and watch the draining liquid, tighten the drain screw 9 when water changes to fuel.
If necessary, ask your engine or equipment supplier for a fresh supply of labels. Apply light film of oil or diesel fuel to the Open fuel shut-off valve. By applying the knowledge in this deutz bfm 1012 bfm 1013 diesel engine service repair manual any owner should be able to make the right decisions about what they need to do to maintain and repair the deutz bfm 1012 bfm 1013 diesel engine. Remove the cooler cap 1 , mount the filling aid and funnel. Carefully remove the gauge without altering the position of the indicator arm. If, however, it is necessary to start and ope- rate the engine without the battery, discon- nect the regulator from the alternator before starting. Fill in the coolant tag and attach in a protected position.